;**************************************
;*         DVRUB                      *
;*  INTERFACE BETWEEN HARDWARE AND IMP*
;*  DATE:  10.OCT.80                  *
;**************************************
 
PS=177776; PROCESSOR STATUS WORD
 
IDLEST=-1; SUPERVISOR IDLE FLAG
 
INTVAL=40; DEDICATED LOCATION FOR INTERRUPT NUMBER
ALARMF=44; DITTO - FOR CLOCK
PSECT=46; DITTO - CURRENT PSECT
LASTPS = 54
INTINF=56
 
UPAR=177640
UPDR=177600
 
UPAR0=40; INDEC INTO PSECT
UPDR0=UPAR0+2; DITTO
UR0=14
UR4=UR0+10; ALL DITTO
UPC=UR0+14
UPS=UR0+16
USP=UR0+20
UTRP=UR0+22
 
 
.=0
0,0
ADDERR, 340
.+2,0
BPTINT,340
.+2,0; 20,22
.+2,0; 24,26; POWER
SVC,340; EMT HANDLER
.+2,0
.+2,0
.+2,0
.+2,0; 50,52
.+2,0; 54,56
 
.=40
INT6BA; FOR USE IN SBLD ONLY

.=60
KBINT,340,TTINT,340
.=70; PR AND PP INT
PRINT,340
LPINT,340

.=100
TIMINT,340
TIMINT,340; ALLOW FOR BOTH CLOCKS
 

.=120;   GRAPH PLOTTER INT
GPINT, 340

.=140;  DUMP ADDRESS
JMP DUMP

.=200; LP (REAL) INT
LPINT,340

.=220; DISC INT
DKINT, 340

.=224; TU16 INT
TU16IT,340
.=230; CR INT
CRINT,340

.=250; SEGMENTATION TRAP
SEGTRP, 340

.=270; BIG DISC INT
RP4INT, 340

.=300; PL11 #1 (TELETYPE), VEC=175610
KB2INT,340
TT2INT,340
;  PL11 #2 (TEXTTRONIC), VEC = 175620
KB3INT,340
TT3INT,340


.=60100;    CODE TO TRAP TOP OF REAL STORE
CLR @#60110
RTI
;
.PAGE
.=1300; LEAVING ROOM FOR SUP STACK
RUN:
MOV PSECT, R3;  GET CURRENT PSECT
BEQ IDLE;   GO INTO IDLE LOOP
MOV R3, R0; PSECT POINTER TO R0
ADD #USP, R0; POINT R0 AT USER SP
CMP LASTPS,R3; SAME AS LAST TIME?
BEQ NOSER; YES, SO DONT RESTORE SEG REGS
MOV R3,LASTPS; MAKE IT TRUE NOW
MOV #UPAR,R1; POINT R1 AT USER SEG REGISTER PAR 0
MOV #UPDR,R2; R2 AT PDR 0
MOV #8.,R5; 8 REGISTERS
ADD #UPAR0,R3; POINT R3 AT REGS IN PSECT
LOOP: MOV (R3)+,(R1)+; SHIFT PAR(N)
MOV (R3),(R2)+; PDR(N)
ADD #10-2,R3; POINT AT NEXT BLOCK
077505;   SOB R5,LOOP; BRACH BACK TILL FINISHED
 
 MOV #030340,PS; SET PREVIOUS MODE=USER
MOV (R0),-(SP); PLANT ON STACK
.WORD 6606;  MTPI R6 - SET R16
NOSER: MOV -(R0), -(SP); PLANT PS ON STACK
MOV -(R0), -(SP); AND PC
MOV -(R0), R5
MOV -(R0),R4
MOV -(R0),R3
MOV -(R0), R2
MOV -(R0), R1
MOV -(R0),R0; RESTORE ALL HIS REGISTERS
.WORD  6;  RTT; AND EXIT TO HIM

IDLE:; IDLE LOOP
   CLR PS
WAIT
BR IDLE

 
DPTAB: 0;  NORMAL BRUN = 0
SAVER4: 0
SAVER5: 0;      MAIN SUPERVISOR PLANTS VALUES HERE

SVC:
JSR R5,SAVE; SAVE THE REGS
MOV UPC-UTRP(R4), R4; PUT HIS PC ON THE STACK
.WORD 6544; MFPI -(R4); GET THE WORD BEFORE THE PC (EMT CODE)
MOVB (SP)+,R1; GET THE CODE (BYTE) INTO R1
EXIT: MOV SAVER4, R4
MOV SAVER5, R5; AND RESTORE R5
EXIT2: RTS PC
 
SAVE:
MOV R4,-(SP)
MOV LASTPS,R4; PSECT ADDR
ADD #UR0,R4; POINT AT USER REGS
MOV R0,(R4)+
MOV R1,(R4)+
MOV R2,(R4)+
MOV R3,(R4)+
MOV (SP)+,(R4)+; R4
MOV (SP)+,(R4)+; R5
MOV (SP)+,(R4)+; PC
MOV (SP)+,(R4)+; PS
.WORD 6506; MFPI R6 - GET USER R6
MOV (SP)+,(R4)+; AND SAVE
MOV R5,PC; AND RETURN
 
INT:  TST PSECT;   IS THERE AN ACTIVE TASK?
     BNE NORMAL; YES, SO SAVE ITS REGISTERS
ADD #4, SP; DUMP PC&PS
MOV #-1,R1; SET INT CODE=-1
BR EXIT2; AND EXIT
 
NORMAL: JSR R5,SAVE; SAVE THE CONTEXT
MOV #-1,R1; SET SERVICE=INTERRUPT
BR EXIT; AND RETURN
 
; *********************************************************
; DEVICE INTERRUPTS
 
KBINT: MOV #-2,INTVAL
BR INT
 
TTINT: MOV #-1,INTVAL
BR INT
 
TIMINT:
CLR INTVAL; INT VALUE=0
BR INT
 
DKINT: MOV #-3, INTVAL
BR INT

SEGTRP: MOV #1, @#52
ERR2: BIT #030000,PS;  PREVIOUS = USER?
BNE ERR3; YES, SO LET THE ERROR THROUGH
HALT; NO, SO WERE IN SUPER STATE (KERNEL HAD IT)
ERR3: MOV #-4,INTVAL
BR INT

ADDERR: MOV #2, @#52
BR ERR2
TU16IT: MOV #-5, INTVAL
BR INT

INT2: BR INT;  IN CASE ITS NEEDED LATER
INT6BA:
; NB: ALL INTS BENEATH MAY BE OVERWRITTEN BY SBLD *************

TXINT: MOV #-6, INTVAL
BR INT

RXINT: MOV #-7, INTVAL
BR INT

RP4INT: MOV #-10, INTVAL
BR INT

LPINT: MOV #-11, INTVAL
BR INT
 
BPTINT: MOV #-12,INTVAL
MOV @SP, INTINF; PASS PC THROUGH
BR INT
KB2INT: MOV #-13,INTVAL
BR INT

TT2INT: MOV #-14, INTVAL
BR INT

KB3INT: MOV #-15, INTVAL
BR INT

TT3INT: MOV #-16, INTVAL
BR INT
MOV #-17, INTVAL
BR INT
CRINT: MOV #-20,INTVAL
BR INT
PRINT: MOV #-21,INTVAL
BR INT
GPINT:   MOV   #-22, INTVAL;      GRAPH PLOTTER
        BR   INT

DTINT:   MOV   #-23, INTVAL
        BR INT
X1INT:   MOV   #-24, INTVAL
        BR INT

X2INT:   MOV   #-25, INTVAL
        BR INT
MOV #-26,INTVAL
BR INT
MOV #-27,INTVAL
BR INT
MOV #-30,INTVAL
BR INT
MOV #-31,INTVAL
BR INT2
MOV #-32,INTVAL
BR INT2
MOV #-33,INTVAL
BR INT2
MOV #-34,INTVAL
BR INT2
MOV #-35,INTVAL
BR INT2
MOV #-36,INTVAL
INTX:BR INT2
MOV #-37,INTVAL
BR INT2
MOV #-40,INTVAL
BR INT2
MOV #-41,INTVAL
BR INT2
MOV #-42,INTVAL
BR INT2
MOV #-43,INTVAL
BR INT2
MOV #-44,INTVAL
BR INT2
MOV #-45,INTVAL
BR INTX
MOV #-46,INTVAL
BR INTX
MOV #-47,INTVAL
BR INTX
MOV #-50,INTVAL
BR INTX
MOV #-51,INTVAL
BR INTX
MOV #-52,INTVAL
BR INTX
MOV #-53,INTVAL
BR INTX
MOV #-54,INTVAL
BR INTX
MOV #-55,INTVAL
BR INTX
MOV #-56,INTVAL
BR INTX
MOV #-57,INTVAL
BR INTX
MOV #-60,INTVAL
BR INTX
MOV #-49.,INTVAL
BR INTX
MOV #-50.,INTVAL
BR INTX

DUMP: MOV #177412, R1;  DUMPER FOR AN RK05
MOV #14124, (R1); DISC ADDRESS
CLR -(R1); CORE ADDRESS=0
MOV #1000002, -(R1); WC = MAX
MOV #3, -(R1); WRITE+GO
DLOOP: TSTB (R1)
BPL DLOOP
MOV #3,(R1); WRITE+GO AGAIN
DLOOP2: TSTB (R1)
BPL DLOOP2
BIT #20000,@#777402
BNE DUMP; NO, SO GO AGAIN
MOV #7, @#777566; BELL ON TT
HALT

.END